Poolside Frankston
Poolside Frankston
Poolside Frankston
Poolside Frankston

Catalogue › HeatingSolarSolar heating

  • Solar heating

     

    Product summary

    Installing solar pool heating can increase the use of your pool by up to four months (more)

  • Product details

  • SOLAR POOL HEATING

    Installing solar pool heating can increase the use of your pool by up to four months. By using the heating energy from the sun, the cost to heat a pool in this way is very economical. The type of solar system may vary; however, the basic principal remains the same. Pool water is circulated through a series of tubes (the collector) usually mounted on the roof, where heat is absorbed and the heated water returned to the pool. The collector can be of either EPDM Rubber or PVC/TPR material and is usually supplied in multiple tube "strips". The amount of heat absorbed and the ultimate increase in pool water temperature depends on several factors which should be considered when deciding on a solar heating system for your pool. They are:

    " Size or area of collector and number of tubes per sq.m

    Naturally the major influence on the effectiveness of any solar system is its exposure to the sun, therefore,

    " Location or positioning of collector

    " Control system

    SIZE OR AREA

    The amount of collector used in your solar system will have a major influence on the effectiveness of the system. The size of the collector is usually expressed in square metres, and as a general rule, directly relates to the surface area of the pool.

    Australian Standard 3634 suggests a minimum collector area equal to 60% of the surface area of the pool.

    * The area of collector generally needs to be increased depending on variables such as; local climate, shading of roof or pool, slope and orientation of roof, wind protection, type and colour of roof and collector type.

    Larger systems will be needed where higher than average water temperature, or extended swimming season is desired.

    In accordance with the above, SPASA recommend a minimum area of 80% for the majority of installations.

    The "area" referred to in relation to collector size is the area of actual collector strip NOT the roof onto which it is to be placed.

    Australian Standard 3634 details the way in which the effective width of collector strip is to be determined for calculating collector area.

    The formula is N x (W + D) where N = number of tubes, D = tube diameter and W = web width between tubes. (The maximum web width which can be used is no more than one tube diameter per tube).

    LOCATION AND ORIENTATION

    Collectors (other than those on flat roofs) should ideally be placed on north facing roofs. Deviation is allowable as long as collector area is increased accordingly. Collector should be located so as to avoid shade from objects i.e.; trees, neighbouring houses etc for at least six hours every day.

    Remember, the following will all affect the size and location of your solar system;

    " Pool surface area

    " Roof orientation

    " Shade on collector or roof

    " Colour of roof and pool

    PUMPING REQUIREMENTS

    To circulate water through the solar system you can choose to use either the existing pump or provide a dedicated pump.

    If the existing pump is to be used it must meet the following conditions;

    (a) the required rate of turnover of the pool water for filtration purposes shall be maintained,

    (b) the operating pressure of the filter shall not be increased above the manufacturer's maximum pressure by the addition of the solar circuit and

    (c) the pump shall have sufficient capacity to handle the static head and friction losses introduced by the addition of the collector circuit.

    The average domestic solar installation requires a minimum flow rate of around 100 to 200 litres per minute to operate effectively. In most circumstances this would mean a dedicated solar pump would be required.

    Always check that the minimum design flow rate of the collector is met when selecting your pump. This flow rate will vary with the diameter of the tubing used.

    The circulated water needs to be strained to avoid blocking up the collector with dirt and debris, so when using a dedicated pump, some form of strainer must be provided.

    Important points:

    " make sure pool filtration requirements are met

    " ensure correct flow rates are obtained

    " circulated water should be strained

    SOLAR CONTROLLERS

    As nobody can guarantee at what time of the day the sun will actually shine, time clocks are of little use in controlling solar heating systems. What is needed is a temperature sensing control device. These units will operate the solar pump system only when heat can be gained. This ensures that maximum heat gain is acquired.

    Circulating water through a cold collector will cool the pool at a faster rate than it can be heated.

    MAJOR POINTS TO REMEMBER:

    " Either EPDM or PVC/TPR material is suitable

    " The size/area of the collector is critical to performance

    " be sure all pumping and filtration requirements are met

    " a temperature sensing controller should be used


HomeTestingAbout usFAQContact usJeffs Handy HintsManualsTestimonialsAwardsMeet The CrewPhotos
 
Another web site powered by the Complete Web system.
Complete Web - Grow your business now!  
 

Poolside Frankston login

Click to login

 

Forgotten password? Reset password to your account, click here.


Don't have an account? Register now - it's simple and free